95 lines
2.6 KiB
TeX
95 lines
2.6 KiB
TeX
|
\documentclass[border=10, convert={outfile=\jobname.png}]{standalone}
|
||
|
|
|
||
|
|
\usepackage[european resistor]{circuitikz}
|
||
|
|
\usetikzlibrary{fit, shapes.misc}
|
||
|
|
\usepackage{siunitx}
|
||
|
|
|
||
|
|
\begin{document}
|
||
|
|
\begin{circuitikz}[]
|
||
|
|
% Raspberry Pi 3B
|
||
|
|
\draw (0.5, 3.5) rectangle (3, -2);
|
||
|
|
\node[right] at (1, 3) {\textbf{Raspi}};
|
||
|
|
|
||
|
|
\draw (3.5, 2) to [short] (2.5, 2) node [left] {GND};
|
||
|
|
\draw (3.5, 0) to [short] (2.5, 0) node [left] {GPIO18};
|
||
|
|
|
||
|
|
\draw (1.75, -1.5) node [above] {USB}
|
||
|
|
to [short] (1.75, -2.5);
|
||
|
|
|
||
|
|
% Bread Board
|
||
|
|
\draw (4, 3.5) rectangle (11.5, -4);
|
||
|
|
\node[right] at (4.5, 3) {\textbf{Breadboard}};
|
||
|
|
|
||
|
|
\draw (3.5, 2) to [short] (4.5, 2) node [circ] {}
|
||
|
|
to [short] (6.5, 2) node [circ] {}
|
||
|
|
to [short] (12, 2);
|
||
|
|
|
||
|
|
\draw (3.5, 0) to [short] (4.5, 0) node [circ] {}
|
||
|
|
to [R, l=$\SI{1.8}{\kilo\ohm}$] (6.5, 0)
|
||
|
|
to [short] (10.5, 0);
|
||
|
|
|
||
|
|
\draw (12, 1)
|
||
|
|
to [short] (10.5, 1)
|
||
|
|
to [R, l_=$\SI{120}{\ohm}$] (8.5, 1)
|
||
|
|
to [empty led, l_=Green] (6.5, 1) node [circ] {};
|
||
|
|
|
||
|
|
\draw (12, -1.5)
|
||
|
|
to [short] (10.5, -1.5)
|
||
|
|
to [R, l_=$\SI{120}{\ohm}$] (8.5, -1.5)
|
||
|
|
to [empty led, l_=Yellow] (6.5, -1.5) node [circ] {};
|
||
|
|
|
||
|
|
\draw (12, -3)
|
||
|
|
to [short] (10.5, -3)
|
||
|
|
to [R, l_=$\SI{120}{\ohm}$] (8.5, -3)
|
||
|
|
to [empty led, l_=Red] (6.5, -3) node [circ] {};
|
||
|
|
|
||
|
|
\draw (11, -3) to [short] (12, -3);
|
||
|
|
|
||
|
|
\draw (4.5, 2) to [R, l=$\SI{2.1}{\kilo\ohm}$] (4.5, 0);
|
||
|
|
|
||
|
|
\draw (6.5, 2) to [short] (6.5, -3);
|
||
|
|
|
||
|
|
\draw (10.5, 1) node [circ] {}
|
||
|
|
to [short] (10.5, 0);
|
||
|
|
|
||
|
|
% Arduino Duemilanove
|
||
|
|
\draw (12.5, 3.5) rectangle (16, -3.5);
|
||
|
|
\node[right] at (13, 3) {\textbf{Arduino}};
|
||
|
|
|
||
|
|
\draw (12, 2) to [short] (13, 2) node [right] {GND};
|
||
|
|
\draw (12, 1) to [short] (13, 1) node [right] {D10};
|
||
|
|
\draw (12, -1.5) to [short] (13, -1.5) node [right] {D11};
|
||
|
|
\draw (12, -3) to [short] (13, -3) node [right] {D12};
|
||
|
|
|
||
|
|
\draw (16.5, 2) to [short] (15.5, 2) node [left] {\SI{5}{\volt}};
|
||
|
|
\draw (16.5, 0) to [short] (15.5, 0) node [left] {D13};
|
||
|
|
|
||
|
|
\draw (15, -3) node [above] {USB}
|
||
|
|
to [short] (15, -4);
|
||
|
|
|
||
|
|
% Sensor
|
||
|
|
\draw (17, 3.5) rectangle (19.5, -0.5);
|
||
|
|
\node[right] at (17.5, 3) {\textbf{Sensor}};
|
||
|
|
|
||
|
|
\draw (16.5, 2) to [short] (18, 2);
|
||
|
|
\draw (16.5, 0) to [short] (18, 0);
|
||
|
|
|
||
|
|
\draw (18, 2) to [normal open switch, name=switch] (18, 0);
|
||
|
|
\node [rounded rectangle, line width=1pt, draw, fit=(switch), inner ysep=1pt, inner xsep=10, rotate=90] at (switch.center) {};
|
||
|
|
|
||
|
|
% USB cable
|
||
|
|
|
||
|
|
\draw (1.75, -2.5)
|
||
|
|
to [short] (1.75, -5)
|
||
|
|
to [short, l=Power for Arduino] (15, -5)
|
||
|
|
to [short] (15, -4);
|
||
|
|
\end{circuitikz}
|
||
|
|
|
||
|
|
\end{document}
|
||
|
|
|
||
|
|
%%% Local Variables:
|
||
|
|
%%% coding: utf-8
|
||
|
|
%%% mode: latex
|
||
|
|
%%% TeX-engine: xetex
|
||
|
|
%%% End:
|